Complete torque converter unit, equipped with NewFren starter belts, suitable for your Piaggio Ciao, Si, Bravo and Boxer moped / moped with variomatic transmission.
High-quality shaft seals, correctly installed shim washers, lubricated needle bearings, a concentricity test and a correctly milled keyway in the torque converter bell characterize this torque converter clutch.
Notes: For installation on a Piaggio Ciao, the pulleys must be turned down to approx. 96 mm or the frame must be ground out a little.
The required belt length in combination with a racing vario is 975 mm for the Ciao (center engine position). For Piaggio Si models it is 1143 mm to 1150 mm.
The installed counter-pressure spring corresponds to the original in terms of spring force. For a higher starting speed, you can replace this with a higher version as required. When fitting, make sure that the spring tab does not protrude too far into the pulley and could damage the belt.
| Manufacturer | GPO |
| Gearbox type | Vario |
| Area of application | Standard |
| Ø outside | 100 mm |
| Hardness level Counter pressure spring | Standard (30 kg - steel-colored) |
| Alternative version of the Piaggio OEM number | 221171, 104649 |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
Hot 
swiing® ingenious pulleys Ø 96 mm | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® ingenious parts · Material: Steel · Material: special bearing bronze · Surface: gas nitrided · Ø Outer pulley: 96 mm · Gearbox type: Vario · Alternative version of the Piaggio OEM number: 103382 · Alternative version of the Piaggio OEM number: 103823 · Alternative version of the Piaggio OEM number: 220923 · Alternative version of the Piaggio OEM number: 220924
CHF 119.90
Not in stock
GPO converter with swiing® pulleys Ø 96 mm | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Manufacturer: swiing® ingenious parts · Ø outside: 96 mm · Gearbox type: Vario · Hardness level Counter pressure spring: Standard (30 kg - steel-colored) · Alternative version of the Piaggio OEM number: 104649 · Alternative version of the Piaggio OEM number: 221171
CHF 179.90
Not in stock
GPO converter Vario Ø 100 mm without bell housing | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Gearbox type: Vario · Ø inside: 93.5 mm · Thickness: 74 mm · Ø outside: 100 mm · Angle pulley: 17 ° · Number of jaws: 3 pcs · Number of springs: 3 pcs · Hardness level Counter pressure spring: Standard (30 kg - steel-colored) · Area of application: Standard · Alternative version of the Piaggio OEM number: 104649 · Alternative version of the Piaggio OEM number: 221171
CHF 109.90
Moped fans also bought
Handlebar fork plate 40 cm curved with chrome strut
Manufacturer: Made in Germany · Material: Steel · Surface: chrome-plated · Mounting type: Fork plate · Clamping diameter: 22 mm · Fork plate holder length: 100 mm · Ø outside: 22 mm · Color: Chrome · Length handlebar ends: 150 mm · Width: 730 mm · Height: 400 mm · Crossbar: Yes · Ø Strut: 14 mm · Strut length: 320 mm
CHF 35.90
swiing® revival locking plate nut Variomatic Inox | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Surface: blank · Ø inside: 8.15 mm · Ø outside: 33.5 mm · Number of lobes: 1 pcs · Area of application: Original · Area of application: Standard
CHF 3.40
Collection only possible with online purchase and appointment.
