Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to mount what:
- Red marking: wheel hub
- Green marking: Brake anchor plate
- Yellow marking: Replacement disk for the speedometer drive (the disk is omitted if a drive is fitted)
- Blue marking: fork leg
Note: When installing the ball bearings, it is important to note that the long spacer bushing must be clamped between the two ball bearings to ensure that the two bearings press against the bushing with the inner ring. If this is not observed, the ball bearings will inevitably jam.
| Thread length | 50 mm, 40.5 mm |
| Ø inside | 12 mm |
| Ø outside | 29.02 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel |
| Surface | galvanized (blue) |
| Thread type | MF12x1 (fine pitch thread) |
| Ø shaft | 11.95 mm |
| Shank length | 74.5 mm |
| Width across flats | 19 mm |
| Ball bearing closed | Yes |
| Total length | 165 mm |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Height | 9.9 mm, 5.9 mm |
| Puch |
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Ø outside: 29.02 mm · Ø shaft: 11.95 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Thread length: 40.5 mm · Thread length: 50 mm · Height: 5.9 mm · Height: 9.9 mm · Shank length: 74.5 mm · Width across flats: 19 mm · Ball bearing closed: Yes
CHF 38.90
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Diameter: 29 mm · Ø outside: 29 mm · Ø shaft: 19 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Width across flats: 19 mm · Ball bearing closed: Yes
CHF 38.90
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Bearing cage: Sheet steel cage ball-guided · Inner ring width: 9 mm · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Material: Plastic · Material: Steel · Ø outside: 29.02 mm · Width: 9 mm · Ball bearing closed: Yes
CHF 8.90
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Manufacturer: GPO · Place of use: left · Place of use: right · Ø axle: 12 mm · Material: Aluminum · Thread type: MF10x1 (fine pitch thread) · Wheel size: 17 " · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm · Ø outside: 41 mm · Total height: 10 mm · Ø mounting hole: 12 mm
CHF 27.90
Explore categories from Hub & axle
Moped fans also bought
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Material: Plastic · Material: Steel · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm · Ball bearing closed: Yes · Area of application: Standard
CHF 5.90
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.9 mm · Ø outside: 11.8 mm · Total length: 185 mm · Thread length: 26 mm · Thread length: 52.5 mm · Shank length: 100 mm · Width across flats: 19 mm
CHF 14.90
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Diameter: 29 mm · Ø outside: 29 mm · Ø shaft: 19 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Shank length: 100 mm · Width across flats: 19 mm · Ball bearing closed: Yes
CHF 38.90
Hot
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Total length: 1600 mm · Total length: 2200 mm
CHF 9.90
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
CHF 30.90
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Stock number: 6001 · Inner ring width: 8 mm · Manufacturer: SKF · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm · Ball bearing closed: Yes
CHF 12.90
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
