Hot 
Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Puch moped / moped with E50 and Z50 engine.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- Optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set piston to TDC, marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel, thus achieving a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good earth (grounding), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal connector:
- 1 = black
- 2 = blue
- 3 = white
Attention: The ignition components stator, rotor, CDI and ignition coil are not compatible with parts of the HPI ignition!
When you buy this complete set, you get a big discount on the retail price of the individual parts.
The ignition is compatible with cable starters, which also fit the HPI, you can find these in the accessories section.
Exclusive product for the highest demands of the quality brand swiing®.
| Manufacturer | swiing® ingenious parts |
| Area of application | Tuning, High End, Racing |
| Light coil voltage | 12 V |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Tension | 12 V |
| Mounting type | Screws |
| Performance | 60 W |
| Ø Internal flywheel | 63.5 mm |
| Ø Flywheel outside | 75 mm |
| Number of fixing points | 3 pcs |
| Puch | E50 Z50 (X30 Sport) |
Accessories & related products
Nos
Hot
BERU Spark Plug Connector, 1 kΩ, Noise-Suppressed, NOS
Ø cable: 5 mm · Ø cable: 7 mm · Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Subcategory: Spark plug connector · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
CHF 9.90
Hot
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Tomos, Beta 521
Width across flats trigger: 27 mm · Width across flats Screw: 19 mm · Manufacturer: GPO · Clamping depth: 10 mm · Material: Steel · Surface: blackened · Area of application: (Dis)assembly tool · Total length: 55 mm · Total length: 75 mm · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Number of components: 1 pcs · Strength class: 8.8
CHF 9.90
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents: 10 ml · Area of application: Chemistry · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
CHF 21.90
CHF 2’190.00/l
swiing® ingenious pull starter EVO & HPI ignition (210) | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Surface: raw · Color: Chrome · Color: black · Ignition system: HPI · Total length: 160 mm · Ø outside: 130 mm · Width: 135 mm · Height: 93 mm · Number of fixing points: 2 pcs · Hole spacing: 137.5 mm
CHF 149.90
Vibration dampener, 8 mm, with M6x10 threads on both sides
Height: 8 mm · Ø outside: 14.7 mm · Manufacturer: Made in Europe · Material: Rubber · Material: Steel · Color: black · Thread type: M6x1 (standard thread) · Total length: 28 mm · Nominal diameter (thread): 6 mm · Thread length: 10 mm
CHF 4.40
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Candle thread type: short · Spark plug socket: M4 · Suppressed: No · Electrode material: Iridium · Width across flats: 21 mm · Thread type: MF14x1.25 (fine pitch thread) · Area of application: Cross · Area of application: High End · Area of application: Tuning
CHF 25.90
12V bulb set (BAX15d) with GPO voltage regulator | Puch
Manufacturer: GPO · Test mark: none · Color: white · Performance: 3 W · Performance: 5 W · Tension: 12 V · Performance: 15 W · Performance: 25 W · Performance: 35 W · Total length: 23 mm · Total length: 51 mm · Bulb holder: BA9s · Bulb holder: BAX15d · Ø base: 9 mm · Ø base: 15 mm · Ø Lamp head: 9 mm · Ø Lamp head: 28 mm · LED: No
CHF 35.90
Ignition cover high "Puch" (old emblem) chrome | Puch E50 / Z50 / ZA50 (wind cooled)
Manufacturer: FAST ARROW · Material: Steel · Surface: chrome-plated · Height: 62 mm · Ø outside: 126 mm · Ø inside: 124 mm · Color: Chrome · Number of fixing points: 2 pcs · Alternative version of the Puch OEM number: 349.1.10.034.1
CHF 39.90
Moped fans also bought
Nos
Hot
BERU Spark Plug Connector, 1 kΩ, Noise-Suppressed, NOS
Ø cable: 5 mm · Ø cable: 7 mm · Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Subcategory: Spark plug connector · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
CHF 9.90
Hot
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Tomos, Beta 521
Width across flats trigger: 27 mm · Width across flats Screw: 19 mm · Manufacturer: GPO · Clamping depth: 10 mm · Material: Steel · Surface: blackened · Area of application: (Dis)assembly tool · Total length: 55 mm · Total length: 75 mm · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Number of components: 1 pcs · Strength class: 8.8
CHF 9.90
Hot
swiing® revival side protection screw set black | Puch Maxi S
Manufacturer: swiing® revival parts · Material: Plastic · Material: Steel · Surface: galvanized (blue) · Surface: raw · Color: silver · Total length: 47 mm · Total length: 60 mm · Drive: Slot · Drive: Triangular head · Thread type: M5x0.8 (standard thread) · Thread length: 35 mm · Thread length: 50 mm
CHF 12.90
Hot
swiing® ingenious 15 mm carburetor camouflaged | Puch
Manufacturer: swiing® ingenious parts · Material: Aluminum · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Area of application: Tuning · Carburetor type: SRE · Choke control: Hand choke · Nominal diameter: 15 mm · Total length: 66 mm · Nozzle thread: M3.5x0.6 (standard thread) · Ø fuel hose connection: 6 mm · Width: 50 mm · Mounting type: Plug connection clamped · Nozzle size: 62 · Height: 95 mm · Ø Inside entrance: 15 mm · Ø Output inside: 15 mm · Ø Air filter connection: 20 mm · Ø Internal connection: 20 mm · Mixed oil connection: No · Vacuum connection: No · Nozzle block: 2.17 · Clamping screw torque (max.): 4 N/m · Alternative version of the Puch OEM number: 349.1.15.100.0 · Alternative version of the Puch OEM number: 349.2.15.800.0 · Alternative version of the Puch OEM number: 349.4.15.500.0 · Alternative version of the Puch OEM number: 349.4.15.000.0 · Alternative version of the Puch OEM number: 349.4.15.300.0 · Alternative version of the Puch OEM number: 349.6.15.400.0 · Alternative version of the Puch OEM number: 349.7.15.700.0 · Alternative version of the Puch OEM number: 349.8.15.400.0 · Alternative version of the Puch OEM number: 349.9.15.300.0
CHF 79.90
Working late? Evening hours on Thursday until 20:00
