Hot 
Complete HRT SX50 KTM clutch suitable for all Puch Maxi mopeds / mopeds with E50 engine.
High-end product, developed for racing purposes and designed for the highest loads. The CNC-machined clutch carriers are manufactured to an accuracy of 0.5 g, which ensures smooth, even running. The metallic lining ensures uncompromising contact pressure and therefore optimum performance.
The clutch hub is equipped with a splined track and fits easily on all common Puch crankshafts. The cone impresses with its precise fit and thanks to the existing thread, you can use your standard Puch clutch puller.
With the specially developed SWAT (Simple Weight Adjustment Technology), the engagement speed can be changed without having to dismantle the clutch. The lining weight can be easily adjusted using the grub screws supplied. It can be varied between 39.5 g and 44 g, which corresponds to an adjustment range of the engagement speed of around 1000 rpm. The grub screws should be glued in with threadlocker (ideally Loctite 243) or tightened to at least 4 Nm.
The scope of delivery includes disk springs instead of conventional springs. This allows the clutch to be adjusted more precisely and the diaphragm springs allow less adjustment than conventional springs. The clutch is supplied partially assembled. The discs are not yet fitted so that you can adjust the spring rates according to your requirements.
We recommend the following basic setting for the first assembly of the spring packs: ()()()()()()()( or total dimension of the stacked disc springs approx. 15.5 mm.
| Manufacturer | Made in Switzerland |
| Material | Steel, Aluminum |
| Area of application | Racing, High End |
| Material addition | Metal |
| Number of jaws | 3 pcs |
| Recording type | Cone mounting |
| Puch | E50 |
Accessories & related products
HRT screw set clutch hub KTM SX50 (strength 10.9) | Puch E50
Material: Steel · Surface: blackened · Nominal diameter (thread): 6 mm · Drive: External hexagon · Screw head: Hexagon · Width across flats: 10 mm · Thread type: M6x1 (standard thread) · Thread length: 25 mm · Number of components: 3 pcs
CHF 8.90
Explore categories from Clutch
Moped fans also bought
swiing® ingenious pull-wire starter PVL ignition | Puch E50
Manufacturer: swiing® ingenious parts · Hole spacing: 138 mm · Material: Plastic · Material: Steel · Surface: chrome-plated · Surface: raw · Color: Chrome · Ignition system: PVL · Width: 150 mm · Height: 80 mm · Ø outside: 130 mm · Total length: 170 mm · Number of fixing points: 2 pcs
CHF 149.90
HPI racing ignition 12V with light 60W
Manufacturer: HPI · Area of application: Tuning · Material: Aluminum · Material: Steel · Ø Internal flywheel: 61.5 mm · Light coil voltage: 12 V · Tension: 12 V · Performance: 60 W · Direction of rotation: left · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Flywheel outside: 71.5 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 6 pcs · Weight: 340 g
CHF 299.90
swiing® ingenious crankshaft "High End" C3/4 & FPM (+1 mm stroke) | Puch E50
Manufacturer: swiing® ingenious parts · Area of application: High End · Cheek type: Full cheeks · Material: Steel · Crankshaft stroke: 44 mm · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø piston pin (B): 12 mm · Ø Bearing seat (clutch side): 17 mm · Thread type: MF10x1 (fine pitch thread) · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Weight: 970 g · Number of gears: 1 pcs
CHF 229.90
Working late? Evening hours on Thursday until 20:00
