41 mm cast iron racing cylinder with Latin American temperament and 57 cc for your Puch M50, MS50, VS50, DS50, VZ50 small motorcycle.
The timing cam of the tuning cylinder was deliberately kept low, which results in particularly good torque in the lower engine speed range.
Thanks to the large sealing surface, no more pouring is required to close the slot on the housing compared to many other cylinder kits.
Compared to the Sombrero racing kit for Puch Velux X30 models, this version has a thinner cylinder neck so that it fits into the corresponding EX50 engine cases.
| Manufacturer | GPO |
| Material | Gray cast iron |
| Displacement | 57 ccm |
| Area of application | Tuning |
| Crankshaft stroke | 43 mm |
| Ø cylinder neck | 43 mm |
| Hole spacing inlet | 42 mm |
| Nominal diameter | 41 mm |
| Ø outlet inside | 25 mm |
| Ø Inlet inside | 19 mm |
| Thread inlet | M6x1 (standard thread) |
| Hole spacing outlet | 42 mm |
| Ø piston pin (B) | 10 mm, 12 mm |
| Hole pattern [mm] | 44 x 44 |
| Outlet type | straight |
| Number of fixing points | 4 pcs |
| Thread outlet | M6x1 (standard thread) |
| Decompressor | No |
| Camouflaged | No |
| Puch | 2-speed MS, MV, MV50 3-speed VSD, DS, VZ, MC |
Accessories & related products
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Manufacturer: Elring · Contents [ml]: 70 ml · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Color: red · Area of application: Chemistry · Gap dimension (max.): 2 mm · Temperature resistance (min.): -60 - 300 °C
CHF 22.90
CHF 327.14/l
GPO cylinder gasket set BAD ASS Lucifer / GPO Sombrero 41 mm | Puch X30 Velux, M50, MS
Manufacturer: GPO · Material: Aluminum · Material: Sealing paper · Number of components: 4 pcs · Thickness: 0.4 mm · Thickness: 0.45 mm · Ø cylinder: 41 mm · Hole spacing inlet: 32 mm · Ø outlet inside: 27 mm · Hole spacing outlet: 32 mm · Hole pattern [mm]: 44 x 44 mm · Decompressor: Yes · Area of application: Tuning
CHF 19.90
GPO Ø 41 mm "Sombrero" cylinder kit | Puch X30 Velux, NG-2AH
Nominal diameter: 41 mm · Manufacturer: GPO · Material: Gray cast iron · Displacement: 57 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 44.7 mm · Ø outlet inside: 25 mm · Ø Inlet inside: 19 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 32 mm · Ø piston pin (B): 10 mm · Ø piston pin (B): 12 mm · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No · Camouflaged: No · Area of application: Tuning
CHF 179.90
CHF 199.90
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Width: 150 mm · Ignition system: BOSCH · Ignition system: DUCATI · Ø outside: 130 mm · Number of fixing points: 2 pcs · Color: Chrome · Color: black-matt · Hole spacing: 137.5 mm · Total length: 160 mm · Height: 88 mm
CHF 149.90
GPO piston 41 mm (12 mm KoBo) | Puch X30 Velux, M50, MS50, VS50, DS50, VZ50
Manufacturer: GPO · Nominal diameter: 41 mm · Ø outside piston (A): 40.94 mm · Ø piston pin (B): 12 mm · Compression height (C): 23.2 mm · Curvature (D): 3.7 mm · Total piston height (E): 49.3 mm · Number of piston rings (F): 2 pcs · Piston ring mold: L-ring · Piston ring mold: Rectangular ring · Piston ring impact: Flank safety device (FS) · Piston ring impact: Internal fuse (IS) · Piston weight: 85 g
CHF 49.90
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width across flats SW: 19 mm · Width: 35.7 mm · Thread type: MF12x1 (fine pitch thread) · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread length: 40.5 mm · Thread length: 50 mm
CHF 38.90
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 19 mm · Ø inside: 12 mm · Diameter: 29 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Ø outside: 29 mm · Width across flats SW: 19 mm · Shank length: 100 mm
CHF 35.80
CHF 38.90
swiing® revival special nut M6 SW8 (sprocket ref. back pedal / intake manifold)
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Thread type: M6x1 (standard thread) · Height: 6 mm · Drive: External hexagon · Width across flats SW: 8 mm
CHF 2.90
Hot 
swiing® ingenious 17 mm SRF carburetor tuning camouflaged | Puch Maxi, Supermaxi, X30 NS / NL
Total length: 65 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Component group Carburetor: Carburetor complete · Area of application: Tuning · Carburetor type: SRE · Nozzle thread: M3.5x0.6 (standard thread) · Nominal diameter: 17 mm · Ø Inside entrance: 17 mm · Ø Internal connection: 23 mm · Width: 47 mm · Ø Output inside: 17.1 mm · Ø Air filter connection: 27.5 mm · Height: 89 mm · Height: 109 mm · Ø fuel hose connection: 5 mm · Mixed oil connection: No · Mounting type: Plug connection clamped · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.2 · Camouflaged: Yes · Nozzle size: 74 · Clamping screw torque (max.): 3 N/m · Clamping screw torque (max.): 4 N/m
CHF 119.90
swiing® revival stud bolt cylinder base M6x26 - 10.9 strength | Sachs
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.8 mm · Thread type: M6x1 (standard thread) · Total length: 26 mm · Thread length: 9 mm · Thread length: 13 mm · Strength class: 10.9
CHF 1.80
Hot
swiing® ingenious intake manifold 17 mm SRF camouflaged | Puch E50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Number of fixing points: 2 pcs · Ø inside: 17 mm · Ø External connection: 23 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Hole spacing inlet: 38 mm · Total height: 53.5 mm · Height flange center hole: 42 mm · Mounting type: Stud bolts & nuts · Total length: 38 mm · Camouflaged: Yes
CHF 44.90
swiing® ingenious intake manifold 17 mm SRF | Puch Z50
Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Material: Aluminum · Ø inside: 17 mm · Ø External connection: 23 mm · Mounting type: Stud bolts & nuts · Hole spacing inlet: 38 mm · Number of fixing points: 2 pcs · Total height: 73 mm · Height flange center hole: 61 mm · Total length: 45 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning
CHF 49.90
Collection only possible with online purchase and appointment.
