BGS Diamond grinder set small 20 pcs.

VELOPUROL Spray 520 ml

Manufacturer: VELOPUROL · Material to be used: Metal · Hazard warning: Extremely flammable aerosol · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause drowsiness and dizziness · Hazard warning: Pressurized container: may burst when heated · Contents [ml]: 520 ml · Signal word: Attention · Hazard pictogram: GHS02 - Highly flammable · Hazard pictogram: GHS07 - Caution dangerous · Area of application: Chemistry · Area of application: Workshop accessories

Sanding/brush set 12 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Material: Nylon · Number of components: 12 pcs · Area of application: Workshop accessories

Kraftwerk needle file set 6 pcs.

Manufacturer: Kraftwerk · Material: Steel · Number of components: 6 pcs · Total length: 160 mm · Area of application: Workshop accessories

3M Scotch-Brite hand pad 15.2 x 22.8 cm

Grain size: 500 · Manufacturer: 3M · Width: 228 mm · Height: 152 mm · Area of application: Workshop accessories

Grinding compound valve 10 g

Manufacturer: Made in Germany · Area of application: Workshop accessories

BGS Compressed air rod grinder 22000 rpm (6 mm holder)

Manufacturer: BGS · Speed: 22000 1/min · Area of application: Workshop accessories

BGS compressed air pin grinder 54,000 rpm (3 mm holder)

Manufacturer: BGS · Speed: 54000 1/min · Area of application: Workshop accessories

Diamond grinding set 30 pcs.

Drive shank Drill chuck: round · Grain size: 125 · Ø drill chuck holder: 3 mm · Material: Diamond · Number of components: 30 pcs · Total length: 45 mm · Area of application: Workshop accessories

BGS milling cutter set carbide small 5 pcs.

Drive shank Drill chuck: round · Manufacturer: BGS · Ø drill chuck holder: 3 mm · Material: Carbide · Number of components: 5 pcs · Area of application: Workshop accessories

Large outlet seal with metal ring

Material: Sealing carton · Material: Sheet metal (steel) · Area of application: Tuning · Reinforced: Yes · Ø outlet inside: 27 mm · Ø screw holder: 6.3 mm · Place of use: Outlet · Thickness: 2.1 mm · Hole spacing outlet: 42.5 mm

swiing® revival stud bolt inlet/outlet M6 x 30 mm (10.9 strength)

Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M6x1 (standard thread) · Diameter: 5.95 mm · Total length: 30 mm · Thread length: 12 mm · Strength class: 10.9

swiing® revival engine revision set (new model) | Puch E50

Manufacturer: swiing® revival parts · Number of components: 7 pcs · Area of application: Tuning

Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing

Ø Stranded wire: 1.25 mm · Nipple shape: Cylinder · Ø nipple: 3 mm · Nipple length: 5 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Cable length: 2200 mm · Number of components: 1 pcs

NGK CR6 Racing ignition cable & plug High End red

Manufacturer: NGK · Material: Rubber · Color: red · Cable available: Yes · Suppressed: Yes · Cable length: 1000 mm · Resistance: 5000 Ω · Component group Carburetor: Ignition cable · Component group Carburetor: Spark plug connector · Ø cable: 7 mm

swiing® revival screw set Motor E50 Inox | Puch Maxi

Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Surface: stainless

swiing® ingenious M6 special nut exhaust flange (hexagon socket) strength 10

Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: M6x1 (standard thread) · Ø outside: 10 mm · Total length: 25 mm · Thread length: 17 mm

BGS compressed air pin grinder 54,000 rpm (3 mm holder)

Manufacturer: BGS · Speed: 54000 1/min · Area of application: Workshop accessories

Milling cutter set tungsten carbide 10 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Material: Tungsten carbide · Number of components: 10 pcs · Total length: 43 mm · Total length: 50 mm · Area of application: Workshop accessories

Carbide cutter set 20 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Material: Carbide · Number of components: 20 pcs · Total length: 38 mm · Area of application: Workshop accessories