Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an MVT license plate.
Made in Switzerland. Designed for the highest loads and proven in racing.
Mounting:
- Starter pinion: Clean the MVT pole wheel, then screw the counterpart for the cable starter onto the pole wheel (secure the enclosed screws with Loctite).
- Pull starter: Position the starter housing in the correct position and tap lightly with a plastic hammer until the pull starter fits perfectly. It can then be screwed into place.
Application:
- Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
- Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Further helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber hammer etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Color | Chrome, black-matt |
| Surface | chrome-plated, raw |
| Ignition system | MVT Allumage |
| Ø outside | 130 mm |
| Number of fixing points | 2 pcs |
| Hole spacing | 138 mm |
| Total length | 170 mm |
| Width | 150 mm |
| Height | 82 mm |
| Puch | E50 |
Ratings
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Color: blue · Contents: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m · Area of application: Chemistry
CHF 21.90
CHF 2’190.00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Chain pitch: 1/2" x 3/16" · Manufacturer: GPO · Material: Steel · Color: Chrome · Surface: chrome-plated · Number of teeth: 28 pcs · Total length: 257 mm · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø outside: 15.9 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
CHF 59.90
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Manufacturer: MVT Allumage · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Tension: 12 V · Weight: 268 g · Direction of rotation: left · Performance: 65 W · Ø mounting plate: 96 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 2 pcs · Ø Flywheel outside: 49.2 mm
CHF 364.90
swiing® ingenious special screw M6x12 drive pinion pull rope starter MVT
Total length: 12 mm · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Drive: Hexagon socket · Screw head: Countersunk head · Thread type: M6x1 (standard thread) · Width across flats: 4 mm
CHF 2.90
Moped fans also bought
MBR clutch basket 18 teeth Racing straight | Puch E50
Manufacturer: MBR · Material: Steel · Toothing type: straight toothed · Ø Receptacle: 31 mm · Number of teeth: 18 pcs · Recording type: Interlocking · Height: 49 mm · Ø inside: 15 mm · Ø inside: 17 mm · Ø outside: 99.5 mm · Area of application: Tuning
CHF 184.90
Hot 
swiing® ingenious crankshaft "High End" with mounted bearings | Puch E50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Weight: 968 g · Crankshaft stroke: 43 mm · Connecting rod length center-center: 90 mm · Number of gears: 1 pcs · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Thread length: 11 mm · Thread length: 15 mm · Ø Connecting rod eye: 15 mm · Ø piston pin (B): 12 mm · Ø Bearing seat (clutch side): 17 mm · Thread type: MF10x1 (fine pitch thread) · Ø Bearing seat (ignition side): 17 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm
CHF 179.90
Not in stock
MVT internal rotor ignition incl. rev limiter & light 12V | Puch / Sachs
Manufacturer: MVT Allumage · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Tension: 12 V · Weight: 268 g · Direction of rotation: left · Performance: 65 W · Ø mounting plate: 96 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 2 pcs · Ø Flywheel outside: 49.2 mm
CHF 364.90
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
