Special electronic capacitor for the breaker ignition system on your moped, scooter, or small motorcycle.
The CDI box uses the breaker only as a timing signal source and simultaneously replaces the capacitor. Problems with worn breaker contacts and low-quality capacitors are now a thing of the past. In addition, your ignition coil can generate higher voltages, which has a positive effect on the maximum RPM in heavily modified engines.
Using the rotary unit built into the ignition module, the ignition timing can be adjusted as needed.
Dimensions: 63 x 67 x 18.5 mm
Advantages of the electronic ignition module:
- No wear and tear
- maintenance-free
- Higher voltage in the upper RPM range
- Higher RPMs possible than with conventional contact ignition
- Easy way to install a shut-off switch or kill switch
Installation:
- Mount the box near the external ignition coil, e.g., on the engine bolt
- Remove the capacitor from your contact ignition
- Connect the breaker to a new wire and route it to the outside. Connect this wire to the right-hand terminal of the module. Be sure to disconnect or remove any other wires that may still be connected to the breaker.
- Connect a wire to ground (e.g., to the frame) from the second terminal from the right on the module.
- Extend or connect a new wire to the pulse coil, route it separately to the outside, and connect it to the third terminal from the right.
- Connect the fourth terminal from the right to your external ignition coil.
Notes: The breaker gap remains at 0.4–0.5 mm. Pay attention to the cable routing within the ignition system to ensure that the cables are not damaged by the rotating flywheel. Your light coil continues to supply the same voltage as before, so there is no need to replace your light bulbs.
The CDI module does not produce clean ignition sparks at RPMs below 700, so this ignition box is primarily suitable for tuned to heavily tuned engines.
You can find additional ignition parts in the accessories section.
A quality product from the Italian manufacturer SparkEVO.
| Manufacturer | SparkEVO |
| Mounting type | Nuts & bolts |
| Connection type | Plug connection |
| Ø mounting hole | 5 mm |
| Area of application | Standard |
| Puch |
| Sachs |
| Piaggio |
Accessories & related products
EFFE breaker with cable | Bosch / Ducati
Manufacturer: EFFE · Material: Steel · Cable available: Yes · Cable length: 100 mm · Ø mounting hole: 4.5 mm · Ø Internal flywheel: 90 mm · Area of application: Original · Area of application: Standard · Ø axle: 4 mm · Number of fixing points: 1 pcs · BOSCH OEM number: 1 217 013 025 · BERU OEM number: 0 340 100 710
CHF 13.90
BOSCH Breaker without cable | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Cable available: No · Ø mounting hole: 4.5 mm · Ø axle: 4 mm · Number of fixing points: 1 pcs · Area of application: Original · Area of application: Standard · BOSCH OEM number: 1 217 013 021 · BERU OEM number: 0 340 100 465
CHF 22.90
BOSCH Breaker without cable reinforced | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Cable available: No · Ø mounting hole: 4.5 mm · Ø Internal flywheel: 90 mm · Ø axle: 4 mm · Number of fixing points: 1 pcs · Area of application: Tuning · Alternative version of the Pony OEM number: A4606 · Alternative version of the Sachs OEM number: 0983 106 000 · BOSCH OEM number: 1 217 013 020 · BERU OEM number: 0 340 100 466
CHF 20.90
Power cable 1-core black 1 mm² (per meter)
Cable cross-section: 1 mm² · Ø single core: 0.15 mm · Manufacturer: Made in Italy · Ordering unit: Per meter · Material: Copper · Material: Plastic · Number of cables: 1 pcs · Surface: raw · Color: black · Total length: 1000 mm · Ø outside: 1.9 mm · Area of application: Standard
CHF 1.50
Moped fans also bought
Magura cable clamp Ø 8 x 15 mm
Manufacturer: Magura · Material: Brass · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Surface: nickel-plated · Thread type: M6x1 (standard thread) · Ø Cable bushing: 2.3 mm · Ø Bundle: 6 mm · Ø outside: 8 mm · Screw head: Hexagon · Total length: 15 mm · Thread length: 7 mm · Drive: External hexagon · Drive: Slot · Width across flats: 7 mm
CHF 2.50
GPO Pulse coil | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Tension: 6 V · Ø mounting hole: 4.6 mm · Ø Internal flywheel: 91 mm · Number of fixing points: 2 pcs · Hole spacing: 50 mm · Mounting type: Screws · Total length: 80 mm · Width: 23.8 mm · Height: 23.8 mm · Area of application: Standard
CHF 24.70
Working late? Evening hours on Thursday until 20:00
