The Spark EVO Zero Basic module (version 2.0) was developed to make the breaker ignition on your Piaggio Ciao, Si, Bravo, Boxer moped / moped significantly more wear-resistant and low-maintenance.
The box only uses the breaker as a clock generator and replaces the capacitor at the same time. Problems with worn breaker contacts and poor quality capacitors are therefore a thing of the past. In addition, your pulse coil can build up higher voltages, which has a positive effect on the upper speed limit of heavily tuned motors.
Advantages of the electronic ignition module:
- No wear
- Maintenance-free
- Higher voltage in the upper speed range
- Higher speeds possible than with conventional contact ignition
- Easy way to install a cut-off switch or kill switch
Mounting:
- Mount the box close to the external ignition coil, e.g. on the motor screw .e.g. on the motor screw
- Remove the capacitor from your contact ignition
- Remove the pulse coil cable and the cable leading to the outside inside your ignition from the breaker
- Connect the breaker with a new cable and lead this to the outside. This is connected to the left contact of the module.
- attach a new cable to the pulse coil (such as
- attach a new cable to the pulse coil (as listed in the accessories) and run this to the outside to the middle connection of the module
- Also attach the cable that runs to the external ignition coil to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. to the motor screw
- .e.g. on the motor screw
Notes: The breaker gap remains at 0.4 - 0.5 mm. Pay attention to the cable routing within the ignition so that they are not damaged by the rotating flywheel.
Your light coil supplies 6 V as before, so there is no need to convert your bulbs to 12 V.
Other parts for your Piaggio ignition system can be found in the accessories section.
Quality product from the Italian manufacturer SparkEVO.
Details
| Manufacturer | SparkEVO |
| Ø mounting hole | 5.3 mm |
| Mounting type | Tab for screwing |
| Connection type | Plug connection, Tab for screwing |
| Area of application | Tuning |
| Height | 33.5 mm, 15.3 mm |
Suitable for the following models
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Luster terminal 3-pole black small (0.1 - 2.5 mm²)
Cable cross-section: 0.1 - 2.5 mm · Clamping diameter: 3.3 mm · Number of connections: 6 pcs · Color: black · Manufacturer: Made in Germany · Total length: 18.5 mm · Width: 22 mm · Height: 15.5 mm · Number of components: 1 pcs · Material: Brass · Material: Plastic · Material: Steel · Area of application: Workshop accessories
CHF 1.40
swiing® revival cable repair set ignition
Color: black · Color: yellow · Cable cross-section [mm²]: 0.75 mm² · Cable cross-section [mm²]: 1 mm² · Ø outside: 1.9 mm · Total length: 300 mm · Ø single core: 0.15 mm · Number of cables: 2 pcs · Manufacturer: swiing® revival parts · Material: Copper · Material: Plastic · Surface: raw · Area of application: Standard
CHF 8.90
GPO breaker without cable (version 2.0) | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Ø axle: 5 mm · Material: Steel · Ø mounting hole: 5 mm · Cable available: No · Number of fixing points: 1 pcs · Area of application: Original · Area of application: Standard · Piaggio OEM number: 103133
CHF 9.90
HPI racing ignition 12V with light breaker housing | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: HPI · Light coil voltage: 12 V · Performance: 60 W · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Internal flywheel: 61.5 mm · Ø Flywheel outside: 140 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 4 pcs · Area of application: Tuning
CHF 349.90
GPO Electronic ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Mounting type: Screws · Number of fixing points: 3 pcs · Area of application: Original · Area of application: Standard · Piaggio OEM number: 181103 · Piaggio OEM number: 219965 · Piaggio OEM number: 244127
CHF 229.90
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Ø cable: 5 mm · Ø cable: 7 mm · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Component group Carburetor: Spraying · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
CHF 8.75
swiing® ingenious puller flywheel | Piaggio Ciao, SI, Bravo, Boxer
Thread type: MF12x1.5 (fine pitch thread) · Thread type: MF17x1 (fine pitch thread) · Width across flats (trigger): 10 mm · Width across flats (trigger): 18 mm · Width across flats Screw: 19 mm · Manufacturer: swiing® ingenious parts · Total length: 100 mm · Area of application: (Dis)assembly tool · Material: Steel · Surface: blackened · Surface: galvanized (blue) · Diameter: 12 mm · Diameter: 24 mm · Number of components: 2 pcs
CHF 17.90
Collection only possible with online purchase and appointment.
