Shaft repair sleeve which can be used on worn, scratched or run-in areas, e.g. on the crankshaft or pinion shaft.
If a shaft is heavily run-in or scratched and can therefore no longer be properly sealed by the oil seal, this Speedi-Sleeve repair sleeve is used.
The 0.2 mm thick chrome steel sleeve is pressed over the shaft using the tool supplied.
Because the shaft is only applied a little, an oil seal with the original dimensions can still be used.
Shaft diameter: 15.0 mm
Width of usable running surface: 5 mm
Material: special, polished chrome steel
Installation instructions:
- Before installation, remove the crankshaft bearing if necessary. If necessary, mount the crankshaft bearing on the shaft, as this can no longer be pressed over the sleeve later.
- Clean the seal sliding surface on the shaft. Remove any unevenness with an abrasive cloth; the sleeve must not be positioned over keyways, holes, threads or other recesses
- Determine the installation position of the repair sleeve on the worn seal sliding surface and mark it precisely. The sleeve must completely cover the damaged area.
- Drive the repair sleeve onto the shaft with light, centric strokes against the impact cap. If the impact cap is too short, a piece of pipe can be used instead. The inside diameter should correspond to that of the impact cap. Ensure that the functional surface of the sleeve is not damaged.
- Do not use any heat during assembly; the use of adhesive is not necessary.
- In the case of large grooves or notches, the sleeve can be pressed on together with some permanently elastic sealing compound.
- If necessary, the flange can be removed by slitting the outer part and using needle-nose pliers.
- Then check everything again for damage and any burrs.
A detailed assembly instruction in English with pictures is included.
Further repair guides, as well as help with fitting oil seals, can be found in the accessories section.
Quality product from the world's leading ball bearing manufacturer SKF.
| Material | Chrome steel (known as Nirosta®) |
| Manufacturer | SKF |
| Number of components | 2 pcs |
| Universal | |
| Sachs | 50 (Fahrtwind, 1.25 / 1.5 hp, DE) 502 (Saxonette) - AL, AML 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 50/4 - MLFB (2.6 PS), LKH (4.5 PS) 503 - AAL, ABL, 2AL / 2BL, AB, AC, ADV 504 (without pedal shaft) 505 (with pedal shaft) - 1A (AT), 2A (HG) 508 - 1 A 535 |
| Pony / Cilo (Beta 521 & 512) | Beta 512 Beta 521 (engine) |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Temperature resistance (min.): -60 - 315 °C · Manufacturer: Elring · Material: Silicone · Contents [ml]: 70 ml · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Area of application: Chemistry · Gap dimension (max.): 2 mm
CHF 19.90
CHF 284.29/l
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Temperature resistance (min.): -60 - 300 °C · Manufacturer: Elring · Contents [ml]: 70 ml · Color: red · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Area of application: Chemistry · Gap dimension (max.): 2 mm
CHF 22.90
CHF 327.14/l
Moped fans also bought
Motorex engine oil (gear oil) manual 450 ml
Temperature resistance (min.): -30 - 220 °C · Manufacturer: Motorex · Oil type: GL4 · Viscosity (SAE): 80W · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Area of application: Gearbox lubrication with clutch
CHF 9.90
CHF 22.00/l
swiing® revival engine seal | Sachs 503 AAL, ABL, AB, AC, ADV, 2AL, 2BL (A1884)
Width: 140 mm · Manufacturer: swiing® revival parts · Total length: 233 mm · Number of fixing points: 9 pcs · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Ø inside: 87 mm · Thickness: 0.4 mm · Pony OEM number: A1884 · Sachs OEM no.: 0250 149 100
CHF 5.40
swiing® revival gearbox cover gasket | Sachs 503 AAL, ABL, AB, AC, ADV, 2AL, 2BL (A1888)
Width: 130 mm · Manufacturer: swiing® revival parts · Total length: 200 mm · Number of fixing points: 6 pcs · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Thickness: 0.35 mm · Pony OEM number: A1888 · Sachs OEM no.: 0250 150 000
CHF 5.40
Dell'Orto 50° carburetor elbow set M6x0.75
Material: Brass · Surface: nickel-plated · Total length: 36.5 mm · Total length: 42 mm · Height: 40 mm · Height: 48 mm · Manufacturer: Dell'Orto · Ø outside: 6 mm · Width across flats nut: 7 mm · Component group Carburetor: Adjusting screws, float, etc. · Internal thread: MF5x0.75 (fine pitch thread) · Thread type: MF6x0.75 (fine pitch thread) · Angle: 50 °
CHF 11.90
swiing® revival manual shift spring | Sachs 50/2, 503 2AL, 2BL (A1337)
Spring design: Tension spring · Material: Spring steel · Surface: burnished · Color: gray · Total length: 28 mm · Length spring hook: 8 mm · Ø wire: 1.25 mm · Manufacturer: swiing® revival parts · Ø outside: 8.5 mm · Ø inside: 6 mm · Pony OEM number: A1337 · Sachs OEM no.: 0239 102 100
CHF 10.90
Not in stock
Speedometer cable VDO (45 - 100 cm) black
Manufacturer: Made in Portugal · Color: black · 4-edge speedometer cable: 1.8 mm · Outer shell length: 450 mm · Outer shell length: 500 mm · Outer shell length: 550 mm · Outer shell length: 600 mm · Outer shell length: 650 mm · Outer shell length: 700 mm · Outer shell length: 750 mm · Outer shell length: 800 mm · Outer shell length: 850 mm · Outer shell length: 900 mm · Outer shell length: 950 mm · Outer shell length: 1000 mm · Thread type: MF10x1 (fine pitch thread)
CHF 8.90
Collection only possible with online purchase and appointment.
