Not so nice 
Pinasco «Slave» engine case with crankshaft (43 mm stroke / 12 mm KoBo) and double intake suitable for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The Pinasco «Power Casing» engine housing is supplied with a crankshaft specially developed for this purpose, which has a wide cheek for controlling the intake.
A standard 13 mm Dellorto SHA carburettor can be fitted to the rear of this housing, as well as any side-mounted carburettor with a 24 mm connection on the diaphragm system. The frame may have to be adapted in this case.
With this dual carburetor system, you can tease the last bit of horsepower out of your racing car.
The following parts are included in the scope of delivery:
- Rear intake flange (connection diameter: 16 mm, Ø-inside: 13 mm)
- Side membrane system incl. sealing plug for the 13 mm flange if this is not used
- Mounting material for diaphragm flange (connection diameter: 24 mm, Ø inside: 20 mm)
- Cylinder stud bolt
- Engine housing (Ø for cylinder neck up to 50.7 mm)
- Engine housing screws
- Crankshaft Pinasco Competition with 43 mm stroke and 12 mm piston pin (axe 12)
- Installation instructions in English & Italian
No housing seal is supplied. Sealing compound is used for sealing
We recommend using the 46 mm Pinasco cylinder kit for this racing gear. In addition, only electronic ignitions can be fitted to this housing.
If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right-hand side of the housing and cylinder. This process is described in the installation instructions.
Corresponding add-on parts such as sealant, racing kit, racing ignition etc. can be found in the accessories section.
Mäsig-läsig! – We strive to offer you the widest range of moped spare parts. However, this product is of rather poor quality and is not recommended by us. Should you nevertheless choose this item, we understand, but cannot offer you any guarantee or exchange.
Quality product from the Italian manufacturer Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Nominal diameter: 19 mm · Manufacturer: Dell'Orto · Component group Carburetor: Carburetor complete · Material: Aluminum · Carburetor type: PHBG CS · Color: black · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 26 mm · Total length: 82 mm · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Mixed oil connection: Yes · Vacuum connection: Yes · Width: 70 mm · Choke control: Hand choke · Height: 124 mm · Choke nozzle size: 60 · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No · Nozzle size: 75 · Area of application: Racing · Area of application: Tuning · Size of secondary nozzle: 45
CHF 119.90
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Malossi · Ø Internal flywheel: 80.5 mm · Material: Steel · Light coil voltage: 12 V · Direction of rotation: right · Weight: 804 g · Weight: 890 g · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Performance: 90 W · Mounting type: Screws · Number of fixing points: 2 pcs · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning
CHF 399.90
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Area of application: Chemistry · Material: Silicone · Color: gray · Contents: 70 ml · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Gap dimension (max.): 2 mm · Temperature resistance (min.): -60 - 315 °C
CHF 19.90
CHF 284.29/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Surface: varnished · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Weight: 650 g · Ø cone small inside: 12.4 mm · Height: 38.7 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Thread length: 7.5 mm · Cone length: 12.5 mm · Cone ratio: 1:5
CHF 209.90
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Nominal diameter: 13 mm · Manufacturer: Dell'Orto · Material: Aluminum · Area of application: Tuning · Component group Carburetor: Carburetor complete · Color: black · Width: 60 mm · Carburetor type: SHA (Piaggio) · Height: 110 mm · Total length: 55 mm · Mounting type: Plug connection clamped · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 18 mm · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.9 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No · Nozzle size: 66
CHF 69.90
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Shaft seal type: A - With rubberized outer part / one sealing lip. · Manufacturer: Malossi · Material: FPM / FKM (colloquially known as Viton) · Surface: rubberized · Width: 5 mm · Place of use: Crankshaft · Ø inside: 15 mm · Temperature resistance (min.): -30 - 200 °C · Ø outside: 24 mm
CHF 14.30
Pinasco 46 mm cylinder kit EVOTEN BIG 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 46 mm · Manufacturer: Pinasco · Material: Aluminum · Area of application: Tuning · Surface: varnished · Displacement: 71 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 49.9 mm · Ø Outlet outside: 22.5 mm · Ø Outlet outside: 25 mm · Ø Outlet outside: 28 mm · Ø outlet inside: 18.5 mm · Ø outlet inside: 20.9 mm · Ø outlet inside: 24.4 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Outlet type: slanted · Hole spacing outlet: 47.5 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 3 pcs · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
CHF 419.90
Pinasco 46 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 46 mm · Manufacturer: Pinasco · Material: Aluminum · Area of application: Tuning · Surface: varnished · Displacement: 71 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 50 mm · Ø Outlet outside: 22.5 mm · Ø outlet inside: 18.5 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Outlet type: slanted · Hole spacing outlet: 48 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 3 pcs · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
CHF 379.90
Explore categories from Gearbox & housing (motor)
Moped fans also bought
WEKEM 2K liquid metal
Manufacturer: WEKEM · Material to be used: Aluminum · Material to be used: Ceramics · Material to be used: Metal · Material to be used: Steel · Material to be used: Wood · Area of application: Chemistry · Color: gray · Contents: 24 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: Toxic to aquatic organisms (with long-term effects) · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Temperature resistance (min.): -20 - 80 °C · Type of application: 2K · Alignment time: 240 sec
CHF 19.90
CHF 398.00/kg
Collection only possible with online purchase and appointment.
