Pinasco «EVOTEN BIG BORE» cylinder with 46 mm bore and 71 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely reworked 46 mm cylinder from Pinasco is now supplied with a 6-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads.Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional screws for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and Ø 10 mm piston pin (axe 10)
- Various gaskets for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating characterize this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be mounted on the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is mounted on a Piaggio Ciao, it must be ground down on the cooling fins on the right-hand side. Due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as on the Ciao or Boxer.
Corresponding add-on parts such as racing gearboxes, racing crankshaft, racing variator etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 71 ccm |
| Nominal diameter | 46 mm |
| Area of application | Tuning |
| Crankshaft stroke | 43 mm |
| Ø piston pin (B) | 10 mm |
| Ø cylinder neck | 50 mm |
| Ø Outlet outside | 22.5 mm |
| Ø outlet inside | 18.5 mm |
| Hole spacing outlet | 48 mm |
| Hole pattern [mm] | 55 x 34 |
| Outlet type | slanted, clamped |
| Number of fixing points | 3 pcs |
| Thread outlet | M6x1 (standard thread) |
| Decompressor | Yes |
| Camouflaged | No |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing cage: Silver cage · Manufacturer: swiing® ingenious parts · Bearing type: Needle roller and cage assembly · Ø inside: 12 mm · Ø outside: 15 mm · Width: 16.2 mm · Dimension needle bearing: 12/15 x 16.2 · Tomos OEM number: 035548
CHF 13.90
Polini Speed Engine electronic ignition housing | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Crankshaft stroke: 43 mm · Ignition type: Electronic · Height: 104 mm · Total length: 215 mm · Width: 175 mm
CHF 209.90
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Crankshaft stroke: 43 mm · Ignition type: Breaker · Height: 104 mm · Total length: 215 mm · Width: 175 mm
CHF 209.90
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Surface: varnished · Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Direction of rotation: right · Height: 38.7 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Cone ratio: 1:5 · Thread length: 7.5 mm · Weight: 650 g
CHF 209.90
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Diameter: 6.2 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M7x1 (standard thread) · Drive: External hexagon · Thread length: 25 mm · Total length: 120 mm · Strength class: 8 · Strength class: 8.8 · Width across flats SW: 11 mm
CHF 11.70
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank - 10.9 strength
Surface: galvanized (blue) · Manufacturer: swiing® ingenious parts · Strength class: 10.9 · Material: Steel · Diameter: 7.3 mm · Total length: 120 mm · Thread type: M7x1 (standard thread) · Thread length: 20 mm · Thread length: 30 mm
CHF 3.90
CHF 4.90
Collection only possible with online purchase and appointment.
