Reinforced pull pin suitable for the manual Z50 engine of Puch X30 Sport NS / NL, as well as Puch X30 Velux mopeds / mopeds.
Execution with axial bearing: The pure axial bearing is designed for extreme loads with very strong clutch springs.
Due to the slightly poorer guidance, however, this bearing can make a little more noise than conventional bearings with a 60° contact angle.
The reinforced clutch springs in the accessories can be used in conjunction with the clutch bearing without any problems.
Adjusting the clutch: Figure 4 shows the position of the clutch release lever in relation to the abutment and the ball collar nut in relation to the clutch release shaft. This setting results in maximum disengagement with minimum effort. Particular attention must be paid to the play between the decoupling shaft and the conical collar nut, as the clutch bearing will inevitably break within a very short time if the play is too small. With the clutch cable engaged, the free travel on the clutch release lever should be approx. 3 mm.
The angle «A» on the picture is 58°. On the hand lever, these clearances result in an empty travel of approx. 1 cm.
Good, inexpensive standard spare part. GPO – GOOD PARTS ONLY.
| Material | Metal |
| Manufacturer | GPO |
| Area of application | Tuning |
| Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-speed MS, MV, MV50 |
Accessories & related products
swiing® revival clutch spring 2-disc version | Puch Z50
Spring design: Pressure spring · Ø wire: 4 mm · Ø inside: 30.5 mm · Manufacturer: swiing® revival parts · Ø outside: 39 mm · Total length: 19.5 mm · Color: gray · Material: Spring steel · Surface: raw · Number of components: 1 pcs · Area of application: Original · Area of application: Standard
CHF 17.90
swiing® ingenious clutch spring reinforced +20% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Total length: 20.5 mm · Material: Spring steel · Surface: coated · Color: blue · Number of components: 1 pcs · Ø inside: 30 mm · Ø outside: 39 mm · Area of application: Tuning
CHF 23.90
swiing® ingenious clutch spring reinforced +40% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Material: Spring steel · Surface: coated · Color: red · Number of components: 1 pcs · Ø outside: 39 mm · Ø inside: 30 mm · Total length: 23.5 mm · Area of application: Tuning
CHF 23.90
Moped fans also bought
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Oil type: GL4 · Viscosity (SAE): 80W · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Temperature resistance (min.): -30 - 220 °C · Area of application: Gearbox lubrication with clutch
CHF 9.90
CHF 22.00/l
swiing® revival shim set crankshaft L17 | Puch Z50
Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Nominal diameter inside: 17 mm · Ø outside: 23.8 mm · Ø inside: 17.1 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.25 mm · Thickness: 0.3 mm
CHF 8.90
swiing® ingenious clutch spring reinforced +20% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Total length: 20.5 mm · Material: Spring steel · Surface: coated · Color: blue · Number of components: 1 pcs · Ø inside: 30 mm · Ø outside: 39 mm · Area of application: Tuning
CHF 23.90
Collection only possible with online purchase and appointment.
