Not so nice 
Engine housing with ball bearings already pressed in, compatible with various Piaggio models (Ciao, Si, Bravo, and Boxer).
Intake port dimensions: 7 x 24 mm
Ø, internal intake diameter: 12 mm
, carburetor connection diameter: 16 mm
The studs, screws, nuts, and washers are included.
So-so! – We strive to offer you the widest selection of moped replacement parts. However, the quality of this product is rather so-so, and we do not recommend it. If you still choose this item, we understand your decision, but we cannot offer any warranty or exchange.
The flat surface of the intake port is too low. The clearance between the crankshaft and the engine block is too large. As a result, the required pre-compression is not achieved. Therefore, only experienced mechanics who can correct this minor flaw should attempt this project.
You can find high-quality alternatives in the accessories section.
| Material | Aluminum |
| Surface | sandblasted |
| Stock number | 6202 |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Polini Speed Engine engine housing electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Color: silver · Total length: 215 mm · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Width: 175 mm · Ignition type: Electronic · Height: 104 mm
CHF 209.90
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Color: silver · Ignition type: Breaker · Total length: 215 mm · Width: 175 mm · Height: 104 mm
CHF 209.90
Explore categories from Gearbox & housing (motor)
Moped fans also bought
Magura Gas/Deco Cable Clamp, Ø 5 x 6 mm
Manufacturer: Magura · Material: Brass · Material: Steel · Surface: nickel-plated · Number of components: 2 pcs · Ø Cable bushing: 1.6 mm · Drive: Slot · Screw head: Lens head · Total length: 6 mm · Thread length: 4 mm · Ø outside: 5 mm · Thread type: M4x0.7 (standard thread)
CHF 2.00
WEKEM 2K Liquid Metal 24 ml
Temperature resistance (min.): -20 - 80 °C · Manufacturer: WEKEM · Material to be used: Aluminum · Material to be used: Ceramics · Material to be used: Metal · Material to be used: Steel · Material to be used: Wood · Contents: 24 ml · Color: gray · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: Toxic to aquatic organisms (with long-term effects) · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Type of application: 2K · Alignment time: 240 sec · Area of application: Chemistry
CHF 19.90
CHF 398.00/kg
Hot 
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao PX / C24, Bravo, SUPERbravo
Nominal diameter: 13 mm · Manufacturer: Dell'Orto · Total length: 46 mm · Width: 60 mm · Material: Aluminum · Area of application: Tuning · Component group Carburetor: Carburetor complete · Color: black · Carburetor type: SHA (Piaggio) · Ø without reducing sleeve: 18 mm · Nozzle size: 66 · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Mounting type: Plug connection clamped · Ø Output inside: 13 mm · Ø Air filter connection: 50.8 mm · Height: 96 mm · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No
CHF 59.90
Not in stock
swiing® revival engine overhaul kit with bearing selection | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: NBR · Material: Oiled paper · Material: Steel · Piaggio OEM number: 112967 · Piaggio OEM number: 113681 · Piaggio OEM number: 182519 · Piaggio OEM number: 241894 · Piaggio OEM number: 480464
CHF 25.50
CHF 22.90
Working late? Evening hours on Thursday until 20:00
