Athena gasket set | Minarelli V1 engine type 1

Elring Curil T2 sealing compound 70 ml (polyurethane) non-hardening green

Temperature resistance (min.): -55 - 250 °C · Manufacturer: Elring · Contents: 70 ml · Color: green · Gap dimension (max.): 0.2 mm · Area of application: Chemistry

Engine revision set Engine | Minarelli V1

Manufacturer: NTN · Area of application: Standard · Number of components: 16 pcs

Polini gasket set cylinder Minarelli V1 engine

Manufacturer: Polini · Number of components: 4 pcs · Ø cylinder: 47 mm · Area of application: Tuning

Athena gasket set | Minarelli V1 engine type 2

Manufacturer: Athena · Number of components: 7 pcs · Area of application: Standard

Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C

Manufacturer: Elring · Material: Silicone · Contents: 70 ml · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Temperature resistance (min.): -60 - 315 °C · Gap dimension (max.): 2 mm · Area of application: Chemistry

Exhaust gasket 24 mm graphite | Minarelli V1 / Morini

Manufacturer: Made in Italy · Place of use: Exhaust · Ø outlet inside: 24 mm · Thickness: 4 mm · Hole spacing inlet: 38 mm

Elring Dirko HT sealing compound red (silicone) high temp. 70 ml elastic up to 315°C

Manufacturer: Elring · Contents: 70 ml · Color: red · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Temperature resistance (min.): -60 - 300 °C · Gap dimension (max.): 2 mm · Area of application: Chemistry

NTN 6203 C3 Ball bearing 17/40/12

Bearing type: Deep groove ball bearing · Stock number: 6203 · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: No · Bearing clearance: C3 · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Area of application: Standard · Material: Steel · Width: 12 mm · Ø inside: 17 mm · Ø outside: 40 mm

Gas cable Ø 1.2 mm x 165 cm (nipple ball) Dell'Orto

Ø nipple: 3.5 mm · Manufacturer: Made in Germany · Number of components: 1 pcs · Material: Steel · Ø Stranded wire: 1.2 mm · Cable length: 1650 mm · Nipple shape: Ball · Surface: galvanized (blue) · Area of application: Standard

Oil seal NBR 17/35/7 A DUO

Shaft seal type: A DUO - With rubberized outer casing / two sealing lips. · Material: NBR · Ø inside: 17 mm · Width: 7 mm · Temperature resistance (min.): -30 - 100 °C · Ø outside: 35 mm

NTN 6202 Ball bearing 15/35/11

Bearing type: Deep groove ball bearing · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: NTN · Ball bearing closed: No · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Steel · Width: 11 mm · Ø inside: 15 mm · Ø outside: 35 mm

Oil seal NBR 15/24/5 AS

Shaft seal type: AS - With rubberized outer casing / one sealing lip / one dust lip. · Material: NBR · Ø inside: 15 mm · Width: 5 mm · Temperature resistance (min.): -30 - 100 °C · Ø outside: 24 mm

Engine revision set Engine | Minarelli V1

Manufacturer: NTN · Area of application: Standard · Number of components: 16 pcs

Jasil crankshaft 12 mm KoBo | Minarelli V1 engine

Manufacturer: Jasil · Cheek type: Full cheeks · Crankshaft stroke: 42 mm · Connecting rod length center-center: 85 mm · Total length of crankpin on clutch side: 70.5 mm · Total length crankpin ignition side: 66.8 mm · Ø crank webs: 74.9 mm · Area of application: Standard · Wide crank webs: 30.9 mm

Polini gasket set cylinder Minarelli V1 engine

Manufacturer: Polini · Number of components: 4 pcs · Ø cylinder: 47 mm · Area of application: Tuning

Clutch shoe set NOS | Minarelli V1

Manufacturer: Minarelli · Number of jaws: 2 pcs · Number of springs: 2 pcs · Area of application: Original · Area of application: Standard